Wallboard plant-manufacture,factory,supplier from China

(Total 24 Products for Wallboard plant)
Because the keel is made of wood, attention must be paid to fire prevention. The standard practice is to evenly apply fireproof coating on the surface of the keel, wait for the entire keel to turn white, and then nail it on the wall to ensure that the area in contact with the wall is also coated with fireproof coating.After the fireproof treatment is completed on the surface of the keel, the assembly can begin. The workers will use a nail gun to fix the joint of the two keels at an angle of 45 degrees.
Contact Now
Because the keel is made of wood, interest should be paid to fireplace prevention. The wellknown exercise is to evenly observe fireproof coating on the floor of the keel, wait fore keel. the complete keel to flip white, and then nail it on the wall to make certain that the place in contact with the wall is additionally lined with fireproof coating.After nailing the keel frame, it is imperative to repair it to the wall.
Contact Now
The rotary dryer for gypsum processing is moreover referred to as the gypsum dryer in the wallboard manufacturing industry.
Contact Now
After shaping the basic shape, use sandpaper to polish the edges of the ceiling and remove any edges or burrs. Be patient and careful when handling, otherwise it will greatly affect the aesthetics in the future.After a few days of hard work, the suspended ceiling at home can be completed.
Contact Now
After shaping the fundamental shape, use sandpaper to polish the edges of the ceiling and cast off any edges or burrs. Be affected person and cautious when handling, in any other case it will notably have an effect on the aesthetics in the future.After a few days of difficult work, the suspended ceiling at domestic can be completed.
Contact Now
According to customer needsMATERIALPlaster, chalk, clay, slurry and filter cake.APPLICATIONHeating Plant of limestone desulfurization project, stone powder maker for high-grade highways, coal grinding mill in environmental protection type boiler plant, the mill in mining firms.Introduction of raw materials of Automatic plaster machineThe Plaster ores are crushed into small granules of the size less than 30mm, conveyed to mills to complete selecting and separating, and then the qualified powder are delivered into fluidized bed boiler for calcinations while the rest return to the mill.
Contact Now
The rotary dryer for gypsum processing is additionally referred to as the gypsum dryer in the wallboard manufacturing industry. Gypsum dryers are regularly used to pre-treat gypsum ore earlier than manufacturing due to the fact they are durable, long-lasting and in a position to stand up to the abrasive nature of mining gypsum ore.The gypsum dryer rotates the material in the drum by lifting a "scraper" mounted inside the drum to spray the gypsum through a stream of hot air.
Contact Now
If the flue gas desulfurization gypsum and coal powder from power plants are not treated in a timely and reasonable manner, a large area of land will be utilized, and even unnecessary secondary pollution will be brought to the environment. Desulfurization gypsum from power plants has the characteristics of high taste and small particles. However, with the widespread application of gypsum method and limestone/wet lime in thermal power plants in China, the production of desulfurization gypsum has rapidly increased due to its by-products.
Contact Now
Plasterboard equipment 1# transverse kiln entry section: it in most cases consists of the automated manipulate of the pipeline of conveyor belt, curler table, solenoid valve, distributor and plate entry accelerator.
Contact Now
Plasterboard machinery 1# transverse kiln entry section: it mainly includes the automatic control of the pipeline of conveyor belt, roller table, solenoid valve, distributor and plate entry accelerator.
Contact Now
Proportioning and molding section: it more often than not consists of gypsum powder metering scale, auxiliary powder scale, two variable frequency slurry pumps, automated manipulate of conveying knife and slurry mixer, molding station mixer, platform vibration motor and different equipment, which can recognise the proportional addition of gypsum powder, auxiliary powder and slurry, and entire the computerized proportioning of the complete system, which can no longer solely retailer personnel,&nb
Contact Now
Gypsum board DescriptionIt is made of excessive exceptional gypsum cloth which is environmental safety and does now not incorporate any dangerous chemicals. Its characteristic of humidity adjustment presents a wholesome residing environment.
Contact Now
Plasterboard equipment 1# transverse kiln entry section: it normally consists of the automated manage of the pipeline of conveyor belt, curler table, solenoid valve, distributor and plate entry accelerator.
Contact Now
Proportioning and molding section: it mainly includes gypsum powder metering scale, auxiliary powder scale, two variable frequency slurry pumps, automatic control of conveying knife and slurry mixer, molding station mixer, platform vibration motor and other equipment, which can realize the proportional addition of gypsum powder, auxiliary powder and slurry, and complete the automatic proportioning of the whole system, which can not only save personnel, but also accurately proportioningCentral control section: the main equipment includes solidification belt forming machine, conveying roller mac
Contact Now
1. Classification of gypsum board from Gypsum board plantThe gypsum boards from Gypsum board plantproduced in China mainly include: paper faced gypsum board, decorative gypsum board, gypsum hollow strip board, fiber ypsum board, gypsum sound-absorbing board, positioning point gypsum board, etc.(l) Paper faced gypsum board. Paper gypsum board is a lightweight board made with gypsum slurry as the core and paper as the cover on both sides. Paper gypsum board is lightweight, high-strength, fire-resistant, mothproof, and easy to process.
Contact Now
Gypsum board DescriptionIt is made of high quality gypsum material which is environmental protection and does not contain any harmful chemicals. Its function of humidity adjustment provides a healthy living environment.
Contact Now
1. Classification of gypsum board from Gypsum board plantThe gypsum boards from Gypsum board plantproduced in China by and large include: paper confronted gypsum board, ornamental gypsum board, gypsum hole strip board, fiber ypsum board, gypsum sound-absorbing board, positioning factor gypsum board, etc.(l) Paper confronted gypsum board. Paper gypsum board is a light-weight board made with gypsum slurry as the core and paper as the cowl on each sides.
Contact Now
Gypsum board production line Decoration and veneer sectionAfter applying adhesive and pressing, the paper gypsum board is flipped over and then applied with adhesive and pressed for curing. After that, it is cut, bound, and stored in boxes.Main Performance of Gypsum Board(1) Low production energy consumption. The unit production energy consumption of the binder gypsum used for producing paper gypsum board is 78% lower than that of cement.(2) Lightweight insulation, using paper faced gypsum board as a partition, weighing only 1/3 1/4 of a brick wall.
Contact Now
Water is brought to the plaster of Paris mixture to shape a slurry of the appropriate consistency. An asphalt emulsion and/or a wax emulsion is brought to acquire the favored degree of moisture resistance in the remaining product. A foaming agent such as a detergent is included, and in the course of the mixing technique air is entrained into the material.
Contact Now
Add foaming agent to the storage tank. When in use, the foaming agent and moisture are respectively sent to the foaming device by the metering pump, and compressed air is introduced to produce stable foam, which is sent to the vertical mixer.After the adhesive is prepared in the tank, it is fed into the spray ports on both sides of the forming station, and the adhesive tape is sprayed onto both sides of the paper gypsum board.
Contact Now
The forming area mainly includes: solidification belt, solidification belt cleaning device, belt deviation corrector, tapered belt, paper feeding wheel, bonding water, forming pressure plate, forming presser foot, spray water, etc. The formed gypsum board is gradually solidified on the solidification belt to meet the requirements of slitting. Both good and bad molding of gypsum board is done here.
Contact Now
Characteristics of gypsum board:1.Sound insulation: Double-layer separation sound insulation partitions made of skinny plates and double-layer sound insulation partitions made of hole strip boards have a sound insulation impact equal to a 24cm thick brick wall, and the sound insulation index can reach 40-50 decibels. 2.Fire resistance: Gypsum board is a non-combustible fabric and has positive fireplace resistance properties.
Contact Now
Product name: Paper Faced Gypsum BoardProduct performance: The paper faced gypsum board has strong points such as light quality, fireproofing, heat preservation, sound insulation, humidification absorbing, easiness for installation and construction, and so on. It is the necessary materials for ornamental and fitment projects such as indoor roof suspending and inside partition wall.Gypsum board is a widely used decorative material in home decoration, which can not only be used for ceiling decoration, but also for wall and floor decoration.
Contact Now
Gypsum board production line Drying sectionThe paper gypsum board is fed into each layer of the 12 layer dryer by a bridge distribution machine according to the program. The dryer is divided into two zones, using hot steam as the heat source. While the hot air paper gypsum board slowly moves forward in the dryer, it continuously exchanges heat with the longitudinally flowing hot air. The board absorbs heat, and the temperature rises. The free water in the board slowly evaporates, but it does not damage the crystalline water of the dihydrate gypsum.
Contact Now
Relate News
Georgia-Pacific held a ribbon cutting recently for their  new $325 million gypsum wallboard production expansion facility.The event was invitation only and included remarks by Georgia-Pacific president of the gypsum business, David Neal, Georgia-Pacific executive vice president of building products, Andy Konieczka and Nolan County Judge Whitley MayDECA Students from Sweetwater High School were also invited to attend the Georgia -Pacific ribbon cutting event.  DECA prepares emerging leaders and entrepreneurs for careers in marketing finance, hospitality and management in hig
While procuring building materials for large real estate developers in New York City, Amanda Kaminsky and her team found that some of the systems to recycle and reuse construction and demolition debris were “far from perfect.”Kaminsky founded Building Product Ecosystems LLC, New York,--a collaboration between building owners, construction management teams, gypsum wallboard manufacturers, concrete producers, recyclers and government agencies--to improve the management systems of major building materials.
Saint-Gobain, a French building products manufacturer, announced plans this week to invest $235 million across the next two years in the expansion and modernization of its CertainTeed gypsum manufacturing facility in Palatka, Florida.Per a company statement, the primary objective of the investment is to increase the production capacity of the existing plant while concurrently improving its energy consumption. The expansion of the facility will also involve the installation of energy-saving equipment and automation technology.
Recently, the second gypsum production line of Guizhou Yongdingshun Gypsum Building Materials Co., Ltd., a key investment attraction project of Guizhou Jinyuan Qianxi Power Plant, has been completed and put into operation. The production line will consume 240000 tons of gypsum and 120000 tons of steam from Qianxi Power Plant annually.It is reported that Guizhou Yongdingshun Gypsum Building Materials Co., Ltd. is a key investment attraction enterprise of Qianxi Power Plant.
PALATKA, Fla.--(BUSINESS WIRE)--Saint-Gobain North America, through its building products subsidiary CertainTeed Interior Products Group, today announced plans to invest $235 million over the next two years to expand its CertainTeed gypsum manufacturing facility in Palatka, Florida, more than doubling the production capacity of the existing manufacturing plant and creating over 100 new, permanent jobs.The expansion of manufacturing and warehouse space in Palatka, which is strategically located near the Port of Jacksonville, comes as Saint-Gobain continues to implement its global Grow and Impac
French materials producer Saint-Gobain has begun production of zero-carbon plasterboard at its modernised plant in Fredrikstad, southeast Norway.The company says its decarbonisation of the manufacturing process was made possible by switching from natural gas to hydroelectric power, thus avoiding 23,000 tons of carbon dioxide emissions a year.Energy is also saved by improved heat recovery and a more efficient manufacturing process, which has reduced energy use at the site by 30% and increased capacity 40%.According to Saint-Gobain, this will enable it to launch a full range of plasterboard prod
Saint-Gobain announces the inauguration of a new plaster and plasterboard factory in Yuzhou, Henan province, China, to set foot on the markets of central and northwestern China. This is the sixth gypsum site of the Group in the country. This new site will produce high-quality paper-faced plasterboards and gypsum powders to respond to the strong demand of the local construction market.
Saint-Gobain North America, through its building products subsidiary CertainTeed Interior Products Group, announced plans July 10 to invest $235 million over the next two years to expand its CertainTeed gypsum manufacturing facility in Palatka.The expansion will more than double the production capacity of the existing manufacturing plant and create more than 100 new jobs, according to a news release.“These are important and high-quality new jobs for our region.
The Bristol expansion will double site capacity and will have a core focus on sustainability.Lightweight construction manufacturer Etex is set to double the plasterboard production capacity of its Ferrybridge plant upon the opening of its new factory in 2023.Work is well underway for the new 57,000m2 Siniat facility, which comes at a time when plasterboard and timber shortages continue to put pressure on the supply chain.The new facility is a significant investment by Etex and demonstrates its commitment to supporting the future of British manufacturing, as well as its eagerness to increase re
The 17th National Gypsum Technology Exchange Conference and Exhibition, as well as the 13th China Building Materials Federation Gypsum Building Materials Branch Annual Meeting in 2023, opened in Yidu City, Hubei Province. More than 40 experts and scholars from various research institutions across the country, as well as over 500 enterprises and nearly 900 representatives, attended the conference.
x

Submitted successfully

We will contact you as soon as possible

Close