Alpha equipment-manufacture,factory,supplier from China

The condition for forming α gypsum is to remove 1.5 water molecules from the dihydrate gypsum in pure saturated steam or in a certain temperature and pressure aqueous solution, and discharge them as liquid water.

Compact equipment , low area coverageThe boiling equipment is vertical-arranged equipment, and the dust remover on the top of the furnace, make a complete body with the furnace .So the equipment is compact and low area coverage.Low energy consumptionThe boiling furnace with low heat and electricity consumption .In the part of energy: Most of the heat is used to dehydration and decomposition, and the rest of small part is used to heat the air from the bottom of the furnace.The heat efficiency of the furnace is above 95%.

Each nozzle is equipped with multiple air outlets, which can freely adjust different wind directions of each nozzle, so that the moisture content error of the same gypsum board in different parts does not exceed 1%Forced dehumidification by fan is conducive to the drying of gypsum board.When adjusting the temperature of the dryer, the cooling and heating adjustment reaction is rapid.The hot blast stove automatically adjusts the coal feeding amount according to the flue gas temperature, with high thermal efficiency.

We also will have short introduction for Wall Plastering Equipment or Wall Plastering Machine. It will introduce how to produce Plaster powder or plaster of paris. The important part of the Plaster Powder Manufacturing is milling system also. We have have a short introduction in the following. Principle of  Wall Plastering Equipment workingThe main principle of drying system: the boiling furnace body is consisting of delicate and intensive cooling coil pipe. Put the heat conductive oil in the pipe, and release the heat into the inside of furnace.

Gypsum board equipment Process flow: Gypsum in the material yard - Calcination - Abrasives - Cooling storage - Clinker measurement - Mixing (water, dry material additives, wet material additives) - Forming (protective paper) - Forming (adhesive edge) - Solidification - Cutting - Drying - Screening - Sawing edge - Sealing edge - StackingAnnual capacity/M2Day capacity(sheet)1200×2400×9mmDrier layerControl system2Million23004PLC4Million46006PLC6Million69008 DCS1.

After shaping the basic shape, use sandpaper to polish the edges of the ceiling and remove any edges or burrs. Be patient and careful when handling, otherwise it will greatly affect the aesthetics in the future.After a few days of hard work, the suspended ceiling at home can be completed.

Plastering Equipment is to grind natural dihydrate Plaster ore (raw Plaster) or industrial by-product Plaster (desulfurization Plaster, phosphoPlaster, etc.) through a dedicated grinding machine and heat and calcine it at a certain temperature to dehydrate and decompose the dihydrate Plaster, resulting in β The product with hemihydrate Plaster (CaSO4.1/2H2O) as the main component is building Plaster (commonly known as Plaster). In summary, there are several main Plastering Equipment processes for Plaster powder:(1) Calcine Plaster blocks and then crush them.This method first places Plaste

We additionally will have quick introduction for Wall Plastering Equipment or Wall Plastering Machine. It will introduce how to produce Plaster powder or plaster of paris. The vital section of the Plaster Powder Manufacturing is milling gadget also. We have have a quick introduction in the following. Principle of Wall Plastering Equipment workingThe principal precept of drying system: the boiling furnace physique is consisting of refined and intensive cooling coil pipe.

Strong equipment processing capacityOur company has high-precision processing equipment (CNC blanking, cutting, planing, automatic welding, shot blasting and other equipment), which can independently control the processing accuracy and quality of the equipment.Our company has advanced testing equipment and perfect quality control means.

Raw materials: Due to the small scale of domestic production lines, raw gypsum is generally not homogenized directly into grinding and calcining.

After shaping the fundamental shape, use sandpaper to polish the edges of the ceiling and cast off any edges or burrs. Be affected person and cautious when handling, in any other case it will notably have an effect on the aesthetics in the future.After a few days of difficult work, the suspended ceiling at domestic can be completed.

Plastering MachineProcessing technologyPhase 1: CrushingThe giant Plaster is overwhelmed through a crusher to a feed fineness of 15mm-50mm that can enter the grinding machine.Phase 2: GrindingThe beaten small portions of Plaster are despatched to the silo via a hoist, and then evenly and quantitatively fed into the grinding chamber of the grinding desktop for grinding via a vibrating feeder.Stage 3: GradingThe Plaster powder after grinding is graded by way of a powder concentrator, and the unqualifie

Plasterboard equipment 1# transverse kiln entry section: it in most cases consists of the automated manipulate of the pipeline of conveyor belt, curler table, solenoid valve, distributor and plate entry accelerator.

Jaw crusher: also called jaw crusher, referred to as broken jaw. Mainly responsible for the rough crushing processing of gypsum. The working principle of extrusion crushing is adopted. The crushing chamber is deep and there is no dead zone, which improves the feeding capacity and output, and the hourly production capacity can reach 2200 tons. The feed size is large and the crushing is uniform, which lays the foundation for the grinding treatment.

Raw materials: Due to the small scale of home manufacturing lines, uncooked gypsum is commonly now not homogenized at once into grinding and calcining.

Plasterboard equipment 1# transverse kiln entry section: it normally consists of the automated manage of the pipeline of conveyor belt, curler table, solenoid valve, distributor and plate entry accelerator.

Strong gear processing capacityOur employer has high-precision processing gear (CNC blanking, cutting, planing, automated welding, shot blasting and different equipment), which can independently manage the processing accuracy and exceptional of the equipment.Our enterprise has superior trying out tools and ideal fine manipulate means.

Plastering MachineProcessing technologyPhase 1: CrushingThe large Plaster is crushed by a crusher to a feed fineness of 15mm-50mm that can enter the grinding machine.Phase 2: GrindingThe crushed small pieces of Plaster are sent to the silo through a hoist, and then evenly and quantitatively fed into the grinding chamber of the grinding machine for grinding through a vibrating feeder.Stage 3: GradingThe Plaster powder after grinding is graded by a powder concentrator, and the unqualified powder is graded by the powder concentrator and returned to the mill host for re grinding.Stage 4: Powder Co

The process of plaster equipment can be summarized as follows: plaster ore → vibrating feeder → jaw crusher → bucket elevator → raw material warehouse → grinding machine → bucket elevator → fluidized bed furnace → bucket elevator → conveyor → clinker warehouse cooling, storage → finished product. The grinding process is particularly crucial.

Plaster and plastering is also widely used in plaster products, such as plaster boards, plaster blocks, etc.The plaster board shape shown in the following figure:Plaster board mainly includes paper faced plaster board, plaster hollow strip board, plaster decorative board, fiber plaster board, etc;Plaster board is a lightweight board made mainly from hemihydrate plaster powder. It has properties such as lightweight, thermal insulation, non combustible, sound-absorbing, and can be sawn and nailed.

Jaw crusher: additionally referred to as jaw crusher, referred to as damaged jaw. Mainly accountable for the tough crushing processing of gypsum. The working precept of extrusion crushing is adopted. The crushing chamber is deep and there is no lifeless zone, which improves the feeding potential and output, and the hourly manufacturing capability can attain 2200 tons.

Jaw crusher: additionally known as jaw crusher, referred to as damaged jaw. Mainly accountable for the difficult crushing processing of gypsum. The working precept of extrusion crushing is adopted. The crushing chamber is deep and there is no lifeless zone, which improves the feeding potential and output, and the hourly manufacturing capability can attain 2200 tons.

Plasterboard equipment instruction1. Plasterboard equipment Batching section of manufacturing machinery: elevator, silo, metering scale, dynamic foaming station, gypsum powder conveying (frequency conversion), slurry conveying machine (frequency conversion), slurry mixing tank and vertical mixer.

According to customer needsMATERIALPlaster, chalk, clay, slurry and filter cake.APPLICATIONHeating Plant of limestone desulfurization project, stone powder maker for high-grade highways, coal grinding mill in environmental protection type boiler plant, the mill in mining firms.Introduction of raw materials of Automatic plaster machineThe Plaster ores are crushed into small granules of the size less than 30mm, conveyed to mills to complete selecting and separating, and then the qualified powder are delivered into fluidized bed boiler for calcinations while the rest return to the mill.